Ruger Wrangler Rimfire $249 MSRP

Ikarus1

Avtomat Krishna-kov
Joined
Dec 16, 2016
Messages
11,128
Location
East of CLT
Rating - 100%
25   0   0
Oops they did it again. I predict a street price around $200.....and Heritage may just dry up and blow away.

https://ruger.com/products/wrangler/models.html

top.jpg
 
They kinda remind me of the old flat gate single six that came out way back in the day.


Sent from my iPhone using Tapatalk
 
it's basically an aluminum single six. Good on them to keep the transfer bar and loading gate interlock. I'll definitely try one out.

I went around and found a good steel US made gun (H&R 949) at the same price point a few years ago, but it was hard. This is easy.
 
Think I read on another sight that the frames are aluminum. I'm honestly surprised there's that much of a demand for another single action but as a huge thumb buster fan, I'm glad to see it.
Me and you both, brother...... it's what I learned on. I'm sure the .22 mag is next.
 
If I did not already have a sweet single-action .22 I would probably be getting in line to buy a Wrangler. Single Sixes are way too pricey to be anywhere close to competitive to the Rough Riders, but the Wrangler will be.
 
When will it be available?
 
I see it weighs 30 ounces. I predict there will be at least one here.
It also takes Single Six grips. I predict you will have more than one, and some bad ass grips installed. I am sure Ruger will make a hundred special editions of it eventually along with Talo and Lipseys
 
I'm guessing that the finish will wear pretty quickly.
 
How does this compare for size relative to Bearcat, Blackhawk, Single Six...? I have a Bearcat now that's great for the kids, but doesn't fit me at all.

Edit: I see it takes Singke Six grips, that should answer my question
 
Last edited:
What’s the reason for keeping these to only six shots? If this thing is as fun as any other 22LR, six shots will be infuriating at the plinking range!

Guess that’s why they’re cheap enough to buy two of them.

I hope it takes clips or there’s a speed loader for it.
 
Last edited:
My old Buffalo Scout has served me well for the last 30 years but I do see her replacement in the wrangler.
 
My FFL buddy says his cost on these is $161.99 but no one is showing any in stock right now. Ruger is usually pretty quick to get a good supply into the chain. I hope to have one before too long.
 
My FFL buddy says his cost on these is $161.99 but no one is showing any in stock right now. Ruger is usually pretty quick to get a good supply into the chain. I hope to have one before too long.
Will you be sending me mine thru fedex, ups or should we ask just ask @fieldgrade for the best avenue?
 
Not available in Minnesota or Massachusetts?

Sent from my SM-G920V using Tapatalk
 
MN bans pot metal guns. Apparently this is one as well...

  • Prohibited: Handguns (other than antique firearms) where the frame, barrel, cylinder, slide or breech-lock is composed of any material with a melting point of less than 1,000 degrees F, or an ultimate tensile strength of less than 55,000 psi, or comprised of any powdered metal having a density of less than 7.5 grams/cubic centimeter.
  • Prohibited: Walther P22, Cobra, Phoenix Arms, and Heritage Arms firearms.
 
MN bans pot metal guns. Apparently this is one as well...

  • Prohibited: Handguns (other than antique firearms) where the frame, barrel, cylinder, slide or breech-lock is composed of any material with a melting point of less than 1,000 degrees F, or an ultimate tensile strength of less than 55,000 psi, or comprised of any powdered metal having a density of less than 7.5 grams/cubic centimeter.
  • Prohibited: Walther P22, Cobra, Phoenix Arms, and Heritage Arms firearms.
Aluminum melts at 1221 degrees Fahrenheit but may not meet the Tensile strength requirements which are ridiculous for a rimfire pistol
 
Last edited:
Aluminum melts at 1221 degrees Fahrenheit but may not meet the Tensile strength requirements which are ridiculous for a rimfire pistol
Unless some other part of the breech is not pure aluminum. Or the alloy used has a low melting point to save money in the mfg process and results in a no go for MN/MA.
 
Last edited:
Unless some other part of the breech is not pure aluminum. Or the alloy used has a low melting point to save money in the mfg process and results in a no go for MN/MA.
Doubtful knowing the metallurgy in other Ruger aluminum firearms. Probably just stupid state laws being stupid. Look at their representatives in Congress for guidance in their lawmaking prowess
 
<puts on moderator hat>

Guys....enough with the Muslim cracks in the open areas of the forum. We have a politics area for that stuff if you're so inclined.
 
Last edited:
Doubtful knowing the metallurgy in other Ruger aluminum firearms. Probably just stupid state laws being stupid. Look at their representatives in Congress for guidance in their lawmaking prowess
For all we know, Ruger contracted this "el cheapo" out. Maybe Heritage is even cranking out some of the parts...
 
MN bans pot metal guns. Apparently this is one as well...

  • Prohibited: Handguns (other than antique firearms) where the frame, barrel, cylinder, slide or breech-lock is composed of any material with a melting point of less than 1,000 degrees F, or an ultimate tensile strength of less than 55,000 psi, or comprised of any powdered metal having a density of less than 7.5 grams/cubic centimeter.
  • Prohibited: Walther P22, Cobra, Phoenix Arms, and Heritage Arms firearms.

Yeah because pot metal, aluminum or other alloy guns can make you more deader than an all steel one. Glad the subjects of MN have people looking after them.
 
Last edited:
For all we know, Ruger contracted this "el cheapo" out. Maybe Heritage is even cranking out some of the parts...

More than likely it's priced like this because Ruger controls their entire production chain, uses CNC and owns Pinetree Castings. I doubt they would stamp the SRC logo on anything cranked out by anyone else. Especially not by Taurus, who owns Heritage.
Depending on the month, Ruger is #1 or #2 in American firearms manufacturing. They're not a shadow of their former selves like Colt or Winchester ;)
 
Last edited:
Back
Top Bottom